sky老白

[作例]【GHL冠军蜃气楼小队】三形态切换TR5 Pathfinder 带改造过程

在最开始,很高兴我们蜃气楼小队拿到了2021年GHL钢普拉队伍王者杯世界公开赛总冠军!而且是最优秀赏&综合部门优胜双料冠军!!我们是来自五湖四海的华人组成的队伍,无数的摩擦和理解将我们凝聚在一起,能够在这个世界级的舞台上一同展现技艺真的非常幸运,必须要对一直支持我们蜃气楼小队的各界朋友们说一声–我们,做到世界冠军了!谢谢你们!!

这里是蜃气楼小队13号机,代号为“Pathfinder”探路者。机体本身没有联邦或吉恩的阵营标,而是使用了我们“蜃气楼小队(TEAM SHINKIROU)”的专用队标。

正如代号的含义,TR-5 Pathfinder在蜃气楼小队的主要职责为开拓航路和远距离运输。

因应小队战术要求,TR-5Pathfinder可进行人形——守护者——飞机形态三段切换,机体整体以高推进力为核心,通过搭载大型战术推进云台为小队实现远距离作战突入及脱离,机体搭载,能源补充,紧急维护等功能,可广泛适应各作战场景的战术要求。而单机状态的TR-5改也是相当优秀的战斗机型,在战术骚扰,火力支援等方面能充分体现单兵价值。



正式照:

各形态图:

细节图:

制作过程:

【主体】:

这只TR5其实制作时间挺久的,中间也经历了很多思考和改动。
This TR5 actually took a long time to make, and it has gone through a lot of thoughts and changes.


胸部加农炮的改造:tr5胸甲中间段切除,骨架底部接一个3mm孔的零件。加农炮的活动扰流板零件反转之后钻出3mm孔,然后接上胶棒。
The transformation of the chest cannon: the middle section of the tr5 breastplate is cut, and a 3mm hole is connected to the bottom of the skeleton. After the movable spoiler part of the cannon is reversed, a 3mm hole is drilled, and then a glue stick is attached.


模仿F1赛车思路,为进排气口推出一条通道。这里不需要锐利的边缘,所以把边缘的翼板切除磨平。
Imitate the idea of F1 car and introduce a channel for the intake and exhaust ports. There is no need for sharp edges here, so cut off and flatten the edges of the wings.


用海瑟斯雷的裙甲作为肩甲使用。原tr5肩膀外甲拆除。可以看到整个主体的线条会更加优秀。裙甲的变形结构也保留了下来,作为tr5的飞行姿态变形使用。
Use Hyze’nthlay-Ⅱ skirt as a shoulder armor. The original tr5 shoulder armor was removed. You can see that the lines of the entire subject will be better. The deformed structure of the skirt armor is also retained and used as the flight attitude deformation of the tr5.


手臂外部的推进盾牌替换成海瑟斯雷腿部,在飞行形态上更符合外观需求。
The propulsion shield on the outside of the arm is replaced with the Hyze’nthlay-Ⅱ’s leg, which is more in line with the appearance requirements in terms of flight configuration.


脚尖的外折部分切除并胶板补缺。原来的后脚跟分件作为折叠扰流板折在末端以完善飞机形态的完整性。
The outer part of the toe is cut off and the rubber plate is used to fill the gap. The original rear heel piece is folded at the end as a folding spoiler to complete the integrity of the aircraft’s form.


由于上身增加了很多内容,原小腿已经不符合整体,替换成叙事高达推进腿部。
Due to the addition of a lot of content to the upper body, the original calf is no longer in line with the whole, and it is replaced with Narrative Gundam’s leg.


膝盖关节进行了pc件的替换,叙事高达的脚板去除,把原来卡栓插槽保留在推进腿内部以方便固定。
The knee joints have been replaced with other PC parts, the foot plate of the Narrative Gundam has been removed, and the original latch slot has been retained inside the push leg for easy fixation.


原推进器前挡板有点难看,所以将其切除。
The front baffle of the original propeller was a bit ugly, so it was cut off.


用tr5零件加波纹板做成前进气装置。
Use tr5 parts and corrugated plates to make the front air intake device.


利用原腿部内部关节和tr5背部推进器组成可开合的腿尖分件。并加上大小一对VF推进喷射器。
Use the original leg internal joints and the tr5 back thruster to form an openable leg tip part. And add a pair of Macross propulsion jets.


天线的改造,突破tr5固有形象改为更自护风格的独角。用的是mg扎古机械风细节天线。改造后和背鳍推进器形成了微妙的关联。
The transformation of the antenna breaks through the inherent image of tr5 . The antenna with mg Zaku mechanical wind detail is used. After modification, it forms a subtle connection with the dorsal fin thruster.


胸部的细节调整,脖子垫高防止缩颈。前胸甲加入了强磁,作用是在飞机形态胸部加农炮抬高到水平的时候可以轻微翘起避免干涉。胸甲后侧的空隙处填补了细节软管。
The details of the chest are adjusted, and the neck is raised to prevent it from being too short. A strong magnet is added to the front breastplate, which is used to slightly tilt up to avoid interference when the aircraft-shaped chest cannon is raised to a level. The gap on the back of the breastplate is filled with detail hoses.


使用mg弗多德尾翼,其形状和功能性非常恰巧的填补了背部的空位。两侧偷胶位置刚好可以用作软管的传输通道。软管的连接使背部各单元有了关联性。
Using MG TR-1 tail wing, its shape and functionality very coincidentally fill the gap in the back. The rubber stolen position on both sides can just be used as the transmission channel of the hose. The connection of the hose makes the back unit related.


胯部关节改造。方式原来的圆球关节,使用了寿屋高强度的关节来替换。从强度,美观性,活动性上都有了较大的提升。
Crotch joint reconstruction. The original ball joints are replaced by Kotobukiya high-strength joints. In terms of strength, aesthetics, and mobility, it has been greatly improved.

【背包】:

基于蜃气楼团队战术需要,TR-5背部需要增加一个大型推进装置,用于满足远距离搭载(运兵),能源补充的战术需求。所以这里首选了mg89飞行基座。
ased on the team’s tactical needs, a large propulsion device needs to be added to the back of the TR-5 to meet the tactical needs of long-distance carrying (troop transport) and energy supplement. The 1/100 Type89 Base Jabber is the first choice here.


假组阶段。主要使用89的燃料槽以及装甲框架。由于体型巨大,整体搭配下来tr5飞行形态全长达到了50cm。
Mainly use Type89 Base fuel tank and armor frame. Due to its huge size, the overall length of the tr5 flight configuration reached 50cm.


89内板拆掉后需要重新处理内部支撑以及框架无缝。把中间段锯开,以作为内部细节填充的窗口。
After the inner panel is removed, it is necessary to re-process the internal support and the frame is seamless. Saw the middle section to serve as a window for filling the inner details.


框架内部添加细节,包括散热板,动力推进装置等等。30mm和狗造确实是好东西。
Add details to the inside of the frame, including heat sinks, power propulsion devices, and so on.


燃料槽外侧用胶板等搭载支撑框架,以承接89外框。
The outer side of the fuel tank is equipped with a support frame such as a rubber sheet to receive the outer frame.


外框原停泊卡位切除替换成可旋转手柄,方便队友“搭车”
The original parking space of the outer frame is removed and replaced with a rotatable handle, which is convenient for teammates to “hitch a ride”

【支架】:

由于tr5改造后体量等于mg,89飞行基座也是mg比例,所以模型整体体积是非常巨大的。设计一个好的支撑点以及支架就显得非常重要了。好的支架还能给作品拍摄上带来很大的帮助。
The overall volume of the model is very huge.It is very important to design a good support point and bracket


承接支架支点我选择在mg tr1全方位推进器组件的燃料槽上。利用原来hg海瑟的胯部关节以及tr系机械臂做成支撑结构。胯部关节装在tr5背部做整体支撑,燃料槽作支架支点。这个关节组合我做了充分的补强,支撑力Max。
I chose the fulcrum for the support bracket to be on the fuel tank of the MG TR-1 omni-directional thruster assembly. Utilize the original hg Hyze’nthlay-Ⅱ’s crotch joints and TR system manipulator arms to make the support structure. The hip joint is installed on the back of the TR-5 for overall support, and the fuel tank is used as the support fulcrum. I have fully reinforced this joint combination, and the support force Max.


亚克力梯形台座是订制的,重量十足。万向节内部添加了粗软铁条,同时保证了强度和多角度展示能力。末端选用双3mm铜支的支撑插杆。
Acrylic trapezoid pedestal is custom-made and it is very heavy. Thick and soft iron bars are added inside the universal joint to ensure strength and multi-angle display capabilities. At the end, a double 3mm copper support rod is used.


长形燃料槽内部贴上强磁,同时在推进器底部也添加强磁组合位置。
A strong magnet is attached to the inside of the long fuel tank, and a strong magnet combination is also added to the bottom of the propeller.


安装后的效果非常稳固。
The effect after installation is very stable.

【局部细节处理】:

模型细节补品很早就有,不论是科幻模型还是军事写实模型等。而过往的细节补品大部分材质是塑料,树脂,金属等等。而近年来3D打印技术的发展给我们带来了新的选择——3D打印件补品。这个新材质给我们带来了更高精度的细节,在合理使用下可以解放模型玩家大量自制细节的时间。而面对日益丰富的细节补品,如何用得恰当用得好看,又成为我们可以讨论的话题。
Model detail supplements have been available for a long time, whether it is a science fiction model or a military realistic model. Most of the past detail supplements are made of plastic, resin, metal and so on. In recent years, the development of 3D printing technology has brought us a new choice-3D printed parts tonics. This new material brings us more high-precision details, which can free up a lot of time for model players to create details under reasonable use. In the face of increasingly rich detailed supplements, how to use them appropriately and beautifully has become a topic we can discuss.


中央推进组件进气口,使用类似机器散热擎片的细节件,这里有进行切割重组并非直接套用。形成更精细的进气口。
The air inlet of the central propulsion component uses details similar to the heat sink of the machine. The cutting and reorganization are not directly applied. Form a finer air inlet.


胸部中央分层细节,由两款细节补品组合而成。胸部是核心位置比较显眼,是添加细节的好地方。
The central detail of the chest is composed of two detail supplements. The chest is more conspicuous at the core and is a good place to add details.


盖层片经打磨处理完全嵌入原套件空隙,遮掩效果显著。两侧的细节补品更多是为了空隙填补。
The heat sink is completely embedded in the gap of the original package after being polished, and the concealing effect is obvious. The detail supplements on both sides are more for gap filling.


进气装置下方的小扰流板是细节点睛之处,也刚好对后面内部作了遮挡。
The small spoiler under the intake device is the finishing touch to the details, and it just happens to cover the rear interior.


背部挡板的细节添加。模型预留的各种孔洞是添加细节的好地方,把空洞填补能够有效提高作品完成度。
The details of the back baffle were added. The various holes reserved for the model are a good place to add details, and filling in the holes can effectively improve the completion of the work.


手臂外挂护甲内部,根据空隙大小打磨散热细节片镶嵌入内,细节效果拉满。
The heat sink is inlaid according to the size of the gap, and the details are full.


大型推进组件的细节添加。细节添加可以是为了美观,功能需求,改造空洞遮掩等等。
The details of the large propulsion components have been added. Details can be added for aesthetics, functional requirements, transformation of vacancies, and so on.

好了,到此为止,感谢大家的耐心收看!

发表回复

  1. free火之红莲说道:

    可以啊,还配了英文

  2. 观星者说道:

    今年的改造作品,我最喜欢探路者

  3. sam说道:

    太复杂了

  4. 半杯西冷茶说道:

    高技术,高成本的制作。这漆面一看就是老手了。

官方微信

Login

跳至工具栏